Solar fórum

Kód: Vybrat vše

homeassistant:
  customize: !include customize.yaml

Kód: Vybrat vše

sensor.battery_charged:
  state_class: total_increasing
  device_class: energy
sensor.battery_discharged:
  state_class: total_increasing
  device_class: energy

Kód: Vybrat vše

esphome:
  name: relay01

esp8266:
  board: esp01_1m

# Enable logging
logger:
  baud_rate: 0 #need this to free up UART pins

# Enable Home Assistant API
api:
  password: "apipassword"

ota:
  password: "otapassword"

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  manual_ip:
    static_ip: 192.168.1.130 # Tady si dejte IP jakou chccete aby relé mělo a samože pak i ostatní parametry vaší sítě níže
    gateway: 192.168.1.2 
    subnet: 255.255.255.0
    
  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Relay01 Fallback Hotspot"
    password: "pinoccio"

captive_portal:
    
uart:
  baud_rate: 115200 # speed to STC15L101EW
  tx_pin: GPIO1
  rx_pin: GPIO3

switch:
  - platform: uart
    name: "A1on"
    data: [0xA0, 0x01, 0x01, 0xA2]

  - platform: uart
    name: "A1off"
    data: [0xA0, 0x01, 0x00, 0xA1]

  - platform: uart
    name: "A2on"
    data: [0xA0, 0x02, 0x01, 0xA3]

  - platform: uart
    name: "A2off"
    data: [0xA0, 0x02, 0x00, 0xA2]
    
  - platform: restart
    name: "2switch_a Restart"
web_server:
    port: 80

Kód: Vybrat vše

# Example configuration.yaml entry
mqtt:
  sensor:
    - state_topic: "home/bedroom/temperature"

Kód: Vybrat vše

sensor:
  - platform: mqtt
    state_topic: "home/bedroom/temperature"

Kód: Vybrat vše

  - platform: mqtt
    name: "bat_watts"
    state_topic: "Inverter/BatteryWatts"
    unit_of_measurement: "W" 
    state_class: measurement
    device_class: energy
  - platform: template
    sensors:
      bat_chrgd:
        value_template: >-
          {% if states('sensor.bat_watts') | float >= 0 %}
          {{ states('sensor.bat_watts') |float(0)/1000}}
          {% endif %}
  - platform: template
    sensors:
      bat_dischrgd:
        value_template: >-
          {% if states('sensor.bat_watts') | float <= 0 %}
          {{ states('sensor.bat_watts') |float(0)/-1000}}
          {% endif %}
  - platform: integration
    source: sensor.bat_chrgd
    name: Battery charged 
    round: 2
  - platform: integration
    source: sensor.bat_dischrgd
    name: Battery discharged 
    round: 2
template:
  - sensor:
    - name: Power Consumption
      state: "{{ state_attr('sensor.pvoutput', 'power_consumption') | float(default=0) }}"
      unit_of_measurement: "W"
    - name: Energy Consumption
      state: "{{ '%0.1f' | format(state_attr('sensor.pvoutput', 'energy_consumption') | float(default=0) / 1000) }}"
      unit_of_measurement: "kWh"
    - name: Power Generation
      state: "{{ state_attr('sensor.pvoutput', 'power_generation') | float(default=0) }}"
      unit_of_measurement: "W"
    - name: Energy Generation
      state: "{{ '%0.2f' | format(state_attr('sensor.pvoutput', 'energy_generation') | float(default=0) / 1000) }}"
      unit_of_measurement: "kWh"